Since they are the most cost-effective and efficient method of purifying drinking water, reverse osmosis (RO) systems have become immensely popular among homes. Furthermore, they have a variety of health advantages. On the other hand, maintaining a drinking water plant is critical to ensuring that it functions at its peak. The following are some things you should look into if you notice that the water flow in your reverse osmosis system is slower than it used to be. There are a variety of causes that might contribute to the slowing of the water flow from your RO filter. You should continue reading to understand more about them to make an educated choice.

What causes your RO Water Flow to be Slow?

Blockage in RO Membrane

The membrane in your reverse osmosis drinking system is delicate and may get clogged rapidly if not replaced at the appropriate time of year. It is recommended that the membrane be replaced every 24 months. However, if you do not take adequate care of it, it might get clogged, causing the water to flow more slowly.

Low Tank Pressure

RO tanks should have a tank pressure of 7-8 psi without any water to function properly. You may check the pressure in the reverse osmosis tank on your own. To investigate this, first, identify where the valve is located. Typically, it may be found towards the bottom of the tank on the side of the tank. Remove all of the water from the tank and use a pressure gauge to check the pressure in the RO water tank.

Ro Tank Bladder that has Ruptured

Your reverse osmosis tank bladder may have ruptured if you can only collect a cup of water from your RO purifier while the water pressure is normal, and subsequently, the flow goes down even more until it is a trickle. Unfortunately, it is not possible to replace the bladder. You’ll have to replace the whole storage tank if this happens. If this is the case, you may seek assistance from specialists in manufacturing mineral water projects.

Filters that have been clogged

The most frequent cause of poor water flow is clogged filters, found in almost every household. Check the filters first if you get the impression that the reverse osmosis tank is not full. According to the manufacturer’s recommendations, ensure that the carbon block, sediment, and GAC polishing filters are replaced. Unless the water in your location has higher levels of pollutants and impurities, you should replace the filters annually.

Kink in the Water Line

Check the water line for kinks and pinches before turning on the water. Ensure that the water supply line valve on your RO system is completely open while you inspect the line.

Reduction in RO Water Pressure

Reverse osmosis is a quick process. Low water pressure in the RO pressure tank may contribute to the poor flow rate from the unit’s water supply. A minimum pressure of 40 psi is required for a RO system to work properly, with an optimal pressure level of 60 psi. Check the pressure in your taps and faucets; if all of them are dripping slowly, likely, your local drinking water plant provider is temporarily operating at a reduced pressure level. You may sit back and wait for the pressure to return. However, if the problem continues and the pressure in the RO tank has been depleted, you should contact a specialist and report the situation.

How do you Inspect your RO System’s Water Flow Rate?

Using the following five easy procedures, you can determine how fast your RO system is delivering water:

• Turn on the water supply line coming into the house. Remove the ball valve located on top of the reverse osmosis system tank and turn it OFF.
• To ensure that the RO faucet remains open, lock it in the Up position.
• Turn on the reverse osmosis system and wait a few minutes until you hear a gradual leak from the system’s faucet.
• Using a measuring cup, record the amount of water that drops into the cup over 60 seconds.
• Take the quantity of water gathered and divide it by 1440 (the number of minutes in a day) to get the total amount of water collected (number of ounces in a gallon).

The figure you come up with is the quantity of water your reverse osmosis system can generate in 24 hours of operation. You will be able to measure the health of your system more accurately now. Alternatively, you may request drinking water plant specialists to come to your house to inspect your RO unit.

Clogged filters or a fouled membrane may be to blame in the case of less flow of RO water, and they will need to be changed to restore the proper flow rate. This page may be useful to you in troubleshooting a range of difficulties connected to your reverse osmosis system, as we detail symptoms, possible causes, and the suggested treatment for each problem.

Get in touch with us for more information on Mineral Water Plant Installation guidelines.